Frequently Asked Questions

111 questions in this forum

1. Calibrating Dimensions

   Asked by bdejong11129, April 22, 2023

   0 votes
   0 answers
2. Unable to print

   Asked by golddustpeak, April 17, 2023

   0 votes
   13 answers
3. adjust default BUTTON macros on klipperscreen??

   Asked by Buurman, April 13, 2023

   0 votes
   1 answer
4. Exclude object Cura

   Asked by nannyogg82, April 3, 2023

   0 votes
   0 answers
5. HIWIN .. is it better??

   Asked by Buurman, February 23, 2023

   • linear rails
   • hiwin
   0 votes
   16 answers
6. Start Macro

   Asked by Wardad5, January 24, 2023

   • macros
   0 votes
   13 answers
7. 1st build - Step motor testing

   Asked by shiftynick, January 28, 2023

   • 2.4r2
   • ldo
   • 350x350
   0 votes
   6 answers
8. Thinking about building a 0.1 Voron; what sort of upgrades should I implement?

   Asked by DennisM, December 29, 2022

   • v0.1
   • mods
   0 votes
   22 answers
9. LED for the enclosure

   Asked by Wardad5, October 18, 2022

   0 votes
   4 answers
10. Auto_Z_Calibration Speed

    Asked by Stadi, January 6, 2023

    0 votes
    6 answers
11. Help Activating Beeper On My 2.4

    Asked by Phil D, December 25, 2022

    • v2.4
    • beeper
    0 votes
    2 answers
12. PCB or Canbus

    Asked by mvdveer, June 29, 2022

    0 votes
    7 answers
13. Voron 1.8 gantry XY joint upper

    Asked by Outofbox11, December 25, 2022

    • v1
    0 votes
    2 answers
14. Caselights macro to turn lights off after a set time.

    Asked by Mcrcheli, December 16, 2022

    • klipper
    • macro
    0 votes
    5 answers
15. Shared TMC drivers SKR Mini E3 V3

    Asked by mvdveer, December 3, 2022

    0 votes
    7 answers
16. MCU Protocol Error After Finally Able to Connect to Moonraker

    Asked by Shadow2, December 1, 2022

    0 votes
    5 answers
17. Euclid Probe Macros. Failure when chamber hot?

    Asked by mvdveer, September 23, 2022

    0 votes
    3 answers
18. First layer issues with possible uneven bed mesh?

    Asked by Wardad5, October 19, 2022

    0 votes
    2 answers
19. Dab of filament at each start causing bulges in the model

    Asked by DennisM, September 30, 2022

    0 votes
    7 answers
20. X-Y Offset settings

    Asked by Delanjp, September 23, 2022

    0 votes
    0 answers
21. Adding an LED to the bottom of an AB-BN toolhead

    Asked by DennisM, September 19, 2022

    0 votes
    3 answers
22. Voron 350mm r2 New Build QGL Help

    Asked by spare_head_3, September 18, 2022

    0 votes
    2 answers
23. Omron Probe and PCB wiring

    Asked by mvdveer, September 9, 2022

    0 votes
    5 answers
24. Adjusting e-steps

    Asked by golddustpeak, September 7, 2022

    0 votes
    9 answers
25. What types of printbeds do y'all use on your Voron?

    Asked by DennisM, September 8, 2022

    0 votes
    7 answers