Frequently Asked Questions

113 questions in this forum

1. Help going grey fast

   Asked by jack separovic, October 10, 2025

   0 votes
   0 answers
2. WIFI connection -> to Raspberry PI5 issue

   Asked by polygonprint, July 20, 2025

   0 votes
   3 answers
3. BTT Manta 8P + Orange Pi CM4 Yes or No?

   Asked by Graymattor, September 5, 2023

   0 votes
   7 answers
4. Please someone share my Z-endstop switch woes!

   Asked by DennisM, September 8, 2022

   1 vote
   10 answers
5. Stepper motor cable length

   Asked by Spigs, May 17, 2025

   0 votes
   8 answers
6. BTT CB1 on a Manta M8P

   Asked by lawson.brian, March 22, 2025

   0 votes
   1 answer
7. Octopus 1.1 successfully flashed but can't find serial/by id. This is my first print build (micron 180) no canbus

   Asked by SunnyShark, March 10, 2025

   0 votes
   3 answers
8. Add or not to add user to group during Klipper installation

   Asked by NewGradRN, February 25, 2025

   0 votes
   2 answers
9. Best alternative Raspberry pi4 (RPI4) with touchscreen for Klipper

   Asked by Buurman, March 7, 2023

   0 votes
   24 answers
10. Voron 2.4R2 start g code macro/Orcaslicer help needed

    Asked by SamppaD, February 2, 2025

    0 votes
    12 answers
11. canbus error after firmware update

    Asked by DC67, January 3, 2025

    0 votes
    5 answers
12. ERCF Crashes on Homing

    Asked by Glenn Coleman, December 23, 2024

    0 votes
    0 answers
13. Adjust the homing speed XY during G28 "Homing".

    Asked by Buurman, December 22, 2022

    0 votes
    5 answers
14. I think I bricked my Octopus 1.1

    Asked by AdSiJu, September 13, 2024

    0 votes
    6 answers
15. Voron 40% infill still the best for Functional Parts?

    Asked by mvdveer, August 2, 2024

    0 votes
    3 answers
16. Can't find bed mesh macro

    Asked by WillyM, July 27, 2024

    0 votes
    4 answers
17. Help needed,Abs+ esun getting soften during 4 hour print to a point that extruding filament fails

    Asked by SamppaD, July 22, 2024

    0 votes
    4 answers
18. Orbiter v2 sensor and happy hare for ercf v2 klipper setup

    Asked by Alphablock23, July 4, 2024

    0 votes
    0 answers
19. How to re-install .cfg files from Git

    Asked by therm_virtual0y, June 23, 2024

    0 votes
    7 answers
20. Any way to customize Klipperscreen?

    Asked by DennisM, September 8, 2022

    0 votes
    7 answers
21. Bed physical location offset from what it should be

    Asked by DennisM, September 7, 2022

    0 votes
    20 answers
22. Buzz stepper test

    Asked by WillyM, June 19, 2024

    0 votes
    5 answers
23. Klipper Error on new build

    Asked by WillyM, June 18, 2024

    0 votes
    13 answers
24. BTT HDMI 5 inteference

    Asked by eviltoy, June 17, 2024

    0 votes
    1 answer
25. Voron 2.4 issues

    Asked by madmike46, May 31, 2024

    0 votes
    3 answers