General Discussion

696 topics in this forum

1. Mainsail access

   By Pappy3831, June 7, 2023
   • 2 replies
   • 2.4k views
   • 
   • Pappy3831
   • June 8, 2023

2. Sourcing question for Voron 2.4 (extra parts)

   By nickpeck47, June 4, 2023
   • 10 replies
   • 8.5k views
   • 
   • claudermilk
   • June 7, 2023

3. Voron TAP - New No probe mod from the Voron Design Team 1 2 3 4 8

   By mvdveer, November 13, 2022   

   • tap
   • probe
   • 197 replies
   • 45.3k views
   • 
   • Penatr8tor
   • June 6, 2023

4. Bed and extruder heater shutting off while executing macros in START_PRINT Macro

   By dghpc, June 3, 2023
   • 0 replies
   • 9.3k views
   • 
   • dghpc
   • June 3, 2023

5. Misumi frame vs LDO blind joint frame Voron 2.4r2

   By SamppaD, May 27, 2023
   • 2 replies
   • 7k views
   • 
   • SamppaD
   • May 29, 2023

6. Need help Defining 0,0 Point

   By bcgreenbox, May 25, 2023
   • 7 replies
   • 5.9k views
   • 
   • bcgreenbox
   • May 26, 2023

7. Mod upgrade Blues..

   By Chuck_Snow, May 24, 2023   

   • canbus
   • tap
   • 6 replies
   • 7.5k views
   • 
   • Chuck_Snow
   • May 26, 2023

8. Multiple cameras?

   By Pappy3831, May 22, 2023
   • 6 replies
   • 3.5k views
   • 
   • Pappy3831
   • May 23, 2023

9. Sense or no sense 1 2

   By Pappy3831, May 15, 2023
   • 31 replies
   • 5.1k views
   • 
   • Pappy3831
   • May 20, 2023

10. Revo High Flow

    By claudermilk, May 17, 2023
    • 0 replies
    • 1.9k views
    • 
    • claudermilk
    • May 17, 2023

11. Extruder Gone Bad

    By claudermilk, May 2, 2023
    • 20 replies
    • 7.8k views
    • 
    • claudermilk
    • May 17, 2023

12. Dead spider?

    By bcgreenbox, May 12, 2023
    • 1 reply
    • 1.4k views
    • 
    • mvdveer
    • May 12, 2023

13. Stealthburner LEDs won’t turn off

    By Mcrcheli, December 20, 2022   

    • stealthburner
    • led
    • 12 replies
    • 16.4k views
    • 
    • Marius j
    • May 7, 2023

14. New Raspberry Pi OS kernel update?

    By ken226, May 4, 2023
    • 2 replies
    • 10.6k views
    • 
    • ken226
    • May 4, 2023

15. Timelapse Filament Retract Settings?

    By ken226, April 28, 2023
    • 1 reply
    • 8.8k views
    • 
    • claudermilk
    • April 28, 2023

16. Part sticking

    By bdejong11129, April 28, 2023
    • 0 replies
    • 1.1k views
    • 
    • bdejong11129
    • April 28, 2023

17. Formbot Kit for Voron 2.4 R2 1 2

    By Buurman, March 8, 2023   

    • formbot
    • 31 replies
    • 11.4k views
    • 
    • claudermilk
    • April 26, 2023

18. Revo ObXidian Nozzles Released

    By mvdveer, April 6, 2023
    • 14 replies
    • 3k views
    • 
    • zogzogzog
    • April 21, 2023

19. Hotend fan riddle

    By mbunjes, April 18, 2023
    • 11 replies
    • 4.1k views
    • 
    • mvdveer
    • April 19, 2023

20. Input Shaping

    By Pierre52, April 16, 2023
    • 21 replies
    • 6.6k views
    • 
    • Pierre52
    • April 19, 2023

21. e-Sun ABS+ ok to use for parts?

    By bdejong11129, April 10, 2023
    • 22 replies
    • 9.5k views
    • 
    • bdejong11129
    • April 14, 2023

22. Filament - lesson learned 1 2

    By mvdveer, March 1, 2023   

    • filament
    • 42 replies
    • 14.6k views
    • 
    • claudermilk
    • April 12, 2023

23. Don't forget to tighten your screws periodicaly

    By Simon2.4, March 28, 2023
    • 6 replies
    • 14.5k views
    • 
    • Aaron
    • April 10, 2023

24. Klipper Buttons for unload and load filament

    By Wick, April 10, 2023
    • 2 replies
    • 14.7k views
    • 
    • claudermilk
    • April 10, 2023

25. Z movement accuracy (2.4motion system) debate

    By Maurici, March 19, 2023
    • 10 replies
    • 8.9k views
    • 
    • Catlord
    • April 10, 2023