General Discussion

696 topics in this forum

1. Earthing...

   By YaaJ, January 8, 2024
   • 8 replies
   • 3.5k views
   • 
   • YaaJ
   • January 11, 2024

2. Induction probe question

   By Juicebx93, January 10, 2024
   • 8 replies
   • 3.2k views
   • 
   • Juicebx93
   • January 11, 2024

3. Voron 2.4 : two questions

   By YaaJ, January 5, 2024
   • 10 replies
   • 7.3k views
   • 
   • YaaJ
   • January 9, 2024

4. Klipper 2024

   By mvdveer, January 3, 2024
   • 9 replies
   • 3.4k views
   • 
   • YaaJ
   • January 6, 2024

5. 3D Printing RC Models

   By PFarm, December 10, 2023
   • 22 replies
   • 2.9k views
   • 
   • PFarm
   • January 5, 2024

6. Second layer problems

   By Cazze, December 31, 2023
   • 15 replies
   • 74.5k views
   • 
   • YaaJ
   • January 4, 2024

7. Question about RGB headers and LED Bars

   By cjkennedy72, December 30, 2023
   • 17 replies
   • 7.2k views
   • 
   • Buurman
   • January 4, 2024

8. Handy JST Pin loader video

   By Ducky4546, December 28, 2023
   • 9 replies
   • 2.4k views
   • 
   • mvdveer
   • January 1, 2024

9. Filametrix

   By YaaJ, December 30, 2023
   • 2 replies
   • 2.5k views
   • 
   • YaaJ
   • January 1, 2024

10. BIQU Microprobe

    By YaaJ, December 17, 2023
    • 3 replies
    • 2.2k views
    • 
    • YaaJ
    • December 27, 2023

11. Switchwire Conversion - Dual Y motors

    By Graymattor, September 5, 2023
    • 21 replies
    • 11.2k views
    • 
    • Paul Trautner
    • December 27, 2023

12. Enraged Rabbit V2 - A Colorful Christmas Present

    By Dirk, December 22, 2023
    • 11 replies
    • 6k views
    • 
    • YaaJ
    • December 25, 2023

13. Voron 0.1 BTT M5P / CB1 Stepper Config issues

    By Titus A Duxass, December 9, 2023
    • 11 replies
    • 9.9k views
    • 
    • TitusADuxass
    • December 24, 2023

14. Voron 2.4 Nozzle Camera suddenly runs slow

    By TimGehres, December 22, 2023
    • 5 replies
    • 7.3k views
    • 
    • TimGehres
    • December 24, 2023

15. Superslicer -- Back again

    By mvdveer, December 17, 2023
    • 4 replies
    • 2.4k views
    • 
    • therm_virtual0y
    • December 23, 2023

16. Voron Test cube dimensional accuracy?

    By Beez1965, December 15, 2023
    • 20 replies
    • 15.1k views
    • 
    • dshess
    • December 22, 2023

17. Wall order

    By YaaJ, December 6, 2023
    • 12 replies
    • 27.1k views
    • 
    • YaaJ
    • December 19, 2023

18. 12 Days of Voronmas

    By Guest, December 11, 2023
    • 1 reply
    • 1.7k views
    • 
    • 3dNutter
    • December 18, 2023

19. Tony Williams

    By Marbuck, December 5, 2023
    • 14 replies
    • 1.9k views
    • 
    • mvdveer
    • December 17, 2023

20. Rust prevention

    By Guest, December 11, 2023
    • 3 replies
    • 1.3k views
    • 
    • 7milesup
    • December 17, 2023

21. LDO Trident Questions

    By kingstar, November 28, 2023
    • 5 replies
    • 1.7k views
    • 
    • kingstar
    • December 13, 2023

22. Octopus board V1.1 has double pins

    By mbunjes, December 4, 2023
    • 12 replies
    • 6.8k views
    • 
    • claudermilk
    • December 11, 2023

23. Stress test

    By YaaJ, December 3, 2023
    • 4 replies
    • 1.6k views
    • 
    • YaaJ
    • December 8, 2023

24. Extruder motor buzzing but not turning

    By bcgreenbox, May 19, 2023
    • 12 replies
    • 13.3k views
    • 
    • Hanna
    • December 8, 2023

25. Nozzle scrub brush is damaging my nozzle tip 1 2

    By Buurman, February 4, 2023   

    • nozzle scrubber
    • 32 replies
    • 12.9k views
    • 
    • WINEDS
    • December 6, 2023