Mini Stealth - Orbiter 2.0 v. 1.2.5

Does the HE Fan have to be the Pi fan or will a 30mm x 30mm x 10mm fan fit?  I can find the 10mm thick fan in 24v flavors.

3 hours ago, Devalis said:

Does the HE Fan have to be the Pi fan or will a 30mm x 30mm x 10mm fan fit?  I can find the 10mm thick fan in 24v flavors.

Yes, the current version will fit a 3010 fan and a spacer clip is needed if using a 3007 fan. The LED wires are tight with the 10mm fan but it should all fit.

Hello again, have you designed any EBB36 mounts that enclose the pcb decently well. I saw some discussions on here but I haven't found any related files yet. Thanks.

2 hours ago, Matei said:

Hello again, have you designed any EBB36 mounts that enclose the pcb decently well. I saw some discussions on here but I haven't found any related files yet. Thanks.

 

Here is the latest mount that I have made to mount an EBB36 on the current version of the Mini Stealth. It can be used with or without the Orbiter filament sensor and includes new cable doors that have a cutout for the new filament release lever (available in the same post).

The PCB sits so far back that I don't know how it could be enclosed. It might be possible to stack a printed cover behind the EBB36 and a small cooling fan could also be added but I haven't tried anything along those lines.

This is an EBB36 mounted on a Mini Stealth v2 but it would look similar on the current version.

On 3/27/2024 at 1:23 PM, atrushing said:

Here is the latest mount that I have made to mount an EBB36 on the current version of the Mini Stealth. It can be used with or without the Orbiter filament sensor and includes new cable doors that have a cutout for the new filament release lever (available in the same post).

The PCB sits so far back that I don't know how it could be enclosed. It might be possible to stack a printed cover behind the EBB36 and a small cooling fan could also be added but I haven't tried anything along those lines.

This is an EBB36 mounted on a Mini Stealth v2 but it would look similar on the current version.

Thank you for the quick response and for the files, are the v2 files currently available too? I need to reprint the housing anyways and I'd like to not have to reprint them again. Thanks!

1 hour ago, Matei said:

Thank you for the quick response and for the files, are the v2 files currently available too? I need to reprint the housing anyways and I'd like to not have to reprint them again. Thanks!

I am currently working on exporting the 428 .stl files.

• 222 different shroud pieces (including CropTop versions)
• 5*12 (60) different core pieces
• 7*4 (28) x-frame sets
• 4 V0 x-carriages
• 4 V0.1/V0.2 XY_joint_upper replacements
• 5 Printers for Ants x-carriage parts
• 3 DAB parts
• 4 probe mounting pieces
• 11 different cable doors
• 7*9 (63) motor bridge and umbilical PCB mounts
• 4 status LED parts and Knomi2 clip
• 4 filament release levers
• 10 customized extruder parts

I will upload them and then I need to make new instructions although the v2 is much easier to install than the current version. I'm not sure how quickly I will be able to finish (and I will be away the week after next) but I plan on making an announcement post that will also outline the changes.

12 hours ago, atrushing said:

I am currently working on exporting the 428 .stl files.

 

• 222 different shroud pieces (including CropTop versions)
• 5*12 (60) different core pieces
• 7*4 (28) x-frame sets
• 4 V0 x-carriages
• 4 V0.1/V0.2 XY_joint_upper replacements
• 5 Printers for Ants x-carriage parts
• 3 DAB parts
• 4 probe mounting pieces
• 11 different cable doors
• 7*9 (63) motor bridge and umbilical PCB mounts
• 4 status LED parts and Knomi2 clip
• 4 filament release levers
• 10 customized extruder parts

 

I will upload them and then I need to make new instructions although the v2 is much easier to install than the current version. I'm not sure how quickly I will be able to finish (and I will be away the week after next) but I plan on making an announcement post that will also outline the changes.

Damn, that's a lot of work. Thanks for the reply.

18 hours ago, atrushing said:

222 different shroud pieces

Amazing.... what a fabulous round number... almost "Monk"ish... I am glad I delayed my V0 build until you did release v2.0

On 3/11/2024 at 4:13 PM, Titus A Duxass said:

It looks good now.

I was checking the MicroProbe in my V0.1 Blender mockup and it will limit X travel by about 8mm.

But it should be a viable probe option when installing the Mini Stealth on an Ender 3. I will be adding a PINDA mount as well as the BL-Touch mount shown here..

On 11/1/2023 at 12:15 AM, nitronaf said:

做了一个测试，进展非常顺利！非常感谢先生。

• Bambulab TZ2.0 热端，带高流量喷嘴
• 醇厚的苍蝇光环
• 零点击
• GDS 3010/4010 标准
• LDO灯丝传感器
• EBB36（仍在发货中）

 

Sir, I would like to know how you placed the FPC connector board for Mellow fly Halo？I also use it in voron 0.1 tri-zero.

• Bambulab TZ2.0 hotend with high flow nozzle
• Mellow fly halo
• Zero click 
• GDS 3010/4010
• Orbiter 2.0
• Mellow fly SHT36V2

12 hours ago, zwj123456789 said:

Sir, I would like to know how you placed the FPC connector board for Mellow fly Halo？I also use it in voron 0.1 tri-zero.

• Bambulab TZ2.0 hotend with high flow nozzle
• Mellow fly halo
• Zero click 
• GDS 3010/4010
• Orbiter 2.0
• Mellow fly SHT36V2

 

This is a good question. I didn't know about this extra board. Unfortunately Mellow doesn't provide any 3D data for the connector board but I will try to figure out the dimensions from your picture or this one from their GitHub.

Can tell me how long the ribbon cable is to help me in finding a mounting place for the board?

8 hours ago, atrushing said:

这是个好问题。我不知道这个额外的板子。不幸的是，Mellow 没有提供连接器板的任何 3D 数据，但我会尝试从您的图片或他们的 GitHub 中找出尺寸。

可以告诉我带状电缆有多长才能帮助我找到电路板的安装位置吗？

FPC-8P-0.5mm-100mm.Sir,I couldn't find a model of this board either, but I have a physical object and can measure its approximate size(21mm*11mm*6mm)

On 5/13/2024 at 6:13 AM, zwj123456789 said:

FPC-8P-0.5mm-100mm.Sir,I couldn't find a model of this board either, but I have a physical object and can measure its approximate size(21mm*11mm*6mm)

How does this look? It holds the PCB in place with an M3x6 BHCS and has a shoulder to keep it straight.

If it works out for you, then I can work this up for the other extruder options.

Orbiter2.0_Cable_Door_Filament_sensor_FlyHalo_FPC.stl

8 hours ago, atrushing said:

这看起来如何？它用 M3x6 BHCS 将 PCB 固定到位，并有一个肩部来保持笔直。

如果它适合您，那么我可以为其他挤出机选项进行处理。

Orbiter2.0_Cable_Door_Filament_sensor_FlyHalo_FPC.stl获取信息...

我只是简单地组装了它

Filametrix - MMU/ERCF Filament Cutter Voron by sorted | Download free STL model | Printables.com

Sir, let's discuss the feasibility of the cutting knife

4 hours ago, zwj123456789 said:

Filametrix - MMU/ERCF Filament Cutter Voron by sorted | Download free STL model | Printables.com

Sir, let's discuss the feasibility of the cutting knife

This would require creating an entire new lever and linkage system and doesn't look very promising. The Mini Stealth is so much smaller than the Stealthburner and doesn't have the structural mass to secure the needed pivot points used by the Filametrix. The lever is also very close to the extruder.

On 5/15/2024 at 6:27 PM, zwj123456789 said:

Filametrix - MMU/ERCF Filament Cutter Voron by sorted | Download free STL model | Printables.com

Sir, let's discuss the feasibility of the cutting knife

 if you need a filament cutter for ercf there is this project

sir , how to Adding Decorative Inlay for mini stealthV2.0?I want to use dual color printing to make it

On 5/31/2024 at 8:59 AM, zwj123456789 said:

sir , how to Adding Decorative Inlay for mini stealthV2.0?I want to use dual color printing to make it

Sorry this took a while. I made new hex-pattern .stl files for the Mini Stealth v2 and I found a video that should work for setting up a dual color pattern print in Bambu Studio. The first minute and a half won't apply since he is creating the inlay from a converted .svg file.

Mini_Stealth_v2_Hex_Pattern.stl Mini_Stealth_v2_Hex_Pattern_UHF.stl

I just found this project and would love to use this with my AWD trident project. But I'll be using 9mm belts. Any chance of a remix to use bigger belts?

1 hour ago, erfont said:

I just found this project and would love to use this with my AWD trident project. But I'll be using 9mm belts. Any chance of a remix to use bigger belts?

I should be able to do that but which probe will you be using?

Also, will you be running an UHF hotend (Rapido/Dragon UHF, VolcoMosq) or a standard height hotend?

Beacon probe, standard height. That would be awesome, thanks!

7 hours ago, atrushing said:

I should be able to do that but which probe will you be using?

Also, will you be running an UHF hotend (Rapido/Dragon UHF, VolcoMosq) or a standard height hotend?

I appreciate you offering to look into this, but hold off for the time being. I ordered one of the new Siboor CNC AWD trident kits that I would like to use your mini stealth on, but it uses a unique CNC carriage that only fits a SB with uhf rapido. Vitiali is working on a universal carriage. I will wait until his is available to work on how to mount the Mini to it. 

11 hours ago, erfont said:

 

I appreciate you offering to look into this, but hold off for the time being. I ordered one of the new Siboor CNC AWD trident kits that I would like to use your mini stealth on, but it uses a unique CNC carriage that only fits a SB with uhf rapido. Vitiali is working on a universal carriage. I will wait until his is available to work on how to mount the Mini to it. 

It looks like it is still a front mounted MGN12 linear carriage so my x-frame set should work just as well if modified for the 9mm belts.

I have added the 9mm belt geometry to the Beacon3D x-carriages (standard and UHF) so you can give it a try when you get your kit.

x_carriage_frames_Beacon3D_MGN12_9mm_Belts.stl x_carriage_frames_Beacon3D_UHF_MGN12_9mm_Belts.stl

sir，This pattern is not applicable to this file   [a]_MiniStealth_Shroud_Orb2.0_ZeroClick_FilSensor_Knomi2