General Discussion

589 topics in this forum

1. Filametrix

   By YaaJ, December 30, 2023
   • 2 replies
   • 1.7k views
   • 
   • YaaJ
   • January 1, 2024

2. BIQU Microprobe

   By YaaJ, December 17, 2023
   • 3 replies
   • 1.5k views
   • 
   • YaaJ
   • December 27, 2023

3. Switchwire Conversion - Dual Y motors

   By Graymattor, September 5, 2023
   • 21 replies
   • 7.9k views
   • 
   • Paul Trautner
   • December 27, 2023

4. Enraged Rabbit V2 - A Colorful Christmas Present

   By Dirk, December 22, 2023
   • 11 replies
   • 4.6k views
   • 
   • YaaJ
   • December 25, 2023

5. Voron 0.1 BTT M5P / CB1 Stepper Config issues

   By Titus A Duxass, December 9, 2023
   • 11 replies
   • 8.5k views
   • 
   • TitusADuxass
   • December 24, 2023

6. Voron 2.4 Nozzle Camera suddenly runs slow

   By TimGehres, December 22, 2023
   • 5 replies
   • 6.4k views
   • 
   • TimGehres
   • December 24, 2023

7. Superslicer -- Back again

   By mvdveer, December 17, 2023
   • 4 replies
   • 1.8k views
   • 
   • therm_virtual0y
   • December 23, 2023

8. Voron Test cube dimensional accuracy?

   By Beez1965, December 15, 2023
   • 20 replies
   • 12.2k views
   • 
   • dshess
   • December 22, 2023

9. Wall order

   By YaaJ, December 6, 2023
   • 12 replies
   • 13.1k views
   • 
   • YaaJ
   • December 19, 2023

10. 12 Days of Voronmas

    By Guest, December 11, 2023
    • 1 reply
    • 1.2k views
    • 
    • 3dNutter
    • December 18, 2023

11. Tony Williams

    By Marbuck, December 5, 2023
    • 14 replies
    • 1.1k views
    • 
    • mvdveer
    • December 17, 2023

12. Rust prevention

    By Guest, December 11, 2023
    • 3 replies
    • 772 views
    • 
    • 7milesup
    • December 17, 2023

13. LDO Trident Questions

    By kingstar, November 28, 2023
    • 5 replies
    • 982 views
    • 
    • kingstar
    • December 13, 2023

14. Octopus board V1.1 has double pins

    By mbunjes, December 4, 2023
    • 12 replies
    • 4.5k views
    • 
    • claudermilk
    • December 11, 2023

15. Stress test

    By YaaJ, December 3, 2023
    • 4 replies
    • 978 views
    • 
    • YaaJ
    • December 8, 2023

16. Extruder motor buzzing but not turning

    By bcgreenbox, May 19, 2023
    • 12 replies
    • 10.7k views
    • 
    • Hanna
    • December 8, 2023

17. Nozzle scrub brush is damaging my nozzle tip 1 2

    By Buurman, February 4, 2023   

    • nozzle scrubber
    • 32 replies
    • 8.6k views
    • 
    • WINEDS
    • December 6, 2023

18. Raspberry Pi5, 3D printer set up guide

    By Graymattor, November 27, 2023
    • 24 replies
    • 33.8k views
    • 
    • mvdveer
    • December 5, 2023

19. Not all painted area generates manual tree support problem?

    By MBPrints, November 25, 2023
    • 1 reply
    • 1.3k views
    • 
    • Penatr8tor
    • December 4, 2023

20. 3D printed clock, Stepper motor

    By Hanna, December 1, 2023
    • 1 reply
    • 1.6k views
    • 
    • atrushing
    • December 1, 2023

21. Filtration

    By Razor1666, November 28, 2023
    • 9 replies
    • 2.4k views
    • 
    • mvdveer
    • November 30, 2023

22. Switched from CW1 to CW2 an have a weird issue.

    By ken226, November 28, 2023
    • 2 replies
    • 10.3k views
    • 
    • ken226
    • November 28, 2023

23. Are there any Klicky Servo Aficionados in here?

    By DIYGuy75, November 11, 2023
    • 1 reply
    • 6.4k views
    • 
    • kenjesse_75
    • November 25, 2023

24. Questions about umbilical + CANBUS on a v2.4

    By YaaJ, November 17, 2023
    • 3 replies
    • 11.6k views
    • 
    • YaaJ
    • November 24, 2023

25. E-Sun Filament - Cardboard spools

    By mvdveer, November 20, 2023
    • 11 replies
    • 3.3k views
    • 
    • YaaJ
    • November 22, 2023