General Discussion

443 topics in this forum

1. Exhaust fan macro?

   By ken226, May 18, 2023
   • 20 replies
   • 3.4k views
   • 
   • claudermilk
   • May 20, 2023

2. Revo High Flow

   By claudermilk, May 17, 2023
   • 0 replies
   • 1.4k views
   • 
   • claudermilk
   • May 17, 2023

3. Extruder Gone Bad

   By claudermilk, May 2, 2023
   • 20 replies
   • 6k views
   • 
   • claudermilk
   • May 17, 2023

4. Dead spider?

   By bcgreenbox, May 12, 2023
   • 1 reply
   • 623 views
   • 
   • mvdveer
   • May 12, 2023

5. Stealthburner LEDs won’t turn off

   By Mcrcheli, December 20, 2022   

   • stealthburner
   • led
   • 12 replies
   • 13.9k views
   • 
   • Marius j
   • May 7, 2023

6. New Raspberry Pi OS kernel update?

   By ken226, May 4, 2023
   • 2 replies
   • 9.8k views
   • 
   • ken226
   • May 4, 2023

7. Timelapse Filament Retract Settings?

   By ken226, April 28, 2023
   • 1 reply
   • 8.1k views
   • 
   • claudermilk
   • April 28, 2023

8. Part sticking

   By bdejong11129, April 28, 2023
   • 0 replies
   • 658 views
   • 
   • bdejong11129
   • April 28, 2023

9. Formbot Kit for Voron 2.4 R2 1 2

   By Buurman, March 8, 2023   

   • formbot
   • 31 replies
   • 5.9k views
   • 
   • claudermilk
   • April 26, 2023

10. Anyone using a BTT Pi TFT43 V2.0? 1 2

    By ken226, March 17, 2023
    • 30 replies
    • 6k views
    • 
    • Slushy_Trout
    • April 23, 2023

11. Revo ObXidian Nozzles Released

    By mvdveer, April 6, 2023
    • 14 replies
    • 1.8k views
    • 
    • zogzogzog
    • April 21, 2023

12. Hotend fan riddle

    By mbunjes, April 18, 2023
    • 11 replies
    • 2.6k views
    • 
    • mvdveer
    • April 19, 2023

13. Input Shaping

    By Pierre52, April 16, 2023
    • 21 replies
    • 2.7k views
    • 
    • Pierre52
    • April 19, 2023

14. e-Sun ABS+ ok to use for parts?

    By bdejong11129, April 10, 2023
    • 22 replies
    • 4.2k views
    • 
    • bdejong11129
    • April 14, 2023

15. Filament - lesson learned 1 2

    By mvdveer, March 1, 2023   

    • filament
    • 42 replies
    • 5.5k views
    • 
    • claudermilk
    • April 12, 2023

16. Don't forget to tighten your screws periodicaly

    By Simon2.4, March 28, 2023
    • 6 replies
    • 13.1k views
    • 
    • Aaron
    • April 10, 2023

17. Klipper Buttons for unload and load filament

    By Wick, April 10, 2023
    • 2 replies
    • 13.1k views
    • 
    • claudermilk
    • April 10, 2023

18. Z movement accuracy (2.4motion system) debate

    By Maurici, March 19, 2023
    • 10 replies
    • 5.9k views
    • 
    • Catlord
    • April 10, 2023

19. Installed a Nozzle Camera - Thought I'd share...

    By StalkS, March 26, 2023   

    • nozzle camera
    • 7 replies
    • 9.9k views
    • 
    • Todd
    • April 10, 2023

20. Worst belt fail ever ?

    By mvdveer, March 31, 2023
    • 5 replies
    • 962 views
    • 
    • Todd
    • April 10, 2023

21. Enraged Rabbit Feeder Print List v1

    By Buurman, April 4, 2023
    • 1 reply
    • 4.3k views
    • 
    • jace055
    • April 9, 2023

22. Embedded Part Printing

    By Penatr8tor, April 6, 2023
    • 2 replies
    • 965 views
    • 
    • claudermilk
    • April 7, 2023

23. Extrude only move too long (-369.461mm vs 50.000mm) Error 1 2

    By 7milesup, March 31, 2023
    • 25 replies
    • 9.2k views
    • 
    • claudermilk
    • April 5, 2023

24. LED strip power question 1 2

    By mbunjes, March 18, 2023   

    • led
    • 28 replies
    • 4.2k views
    • 
    • VoronManiac
    • April 1, 2023

25. Phaetus Rapido Plus Hotend UHF

    By Gimmi, March 23, 2023
    • 1 reply
    • 2k views
    • 
    • mheath82
    • March 30, 2023