General Discussion

433 topics in this forum

1. Bigtreetech Pi V1.2 Unboxing

   By mvdveer, May 12, 2023
   • 9 replies
   • 3.2k views
   • 
   • PFarm
   • August 25, 2023

2. Voron V0 rear panel mod

   By Champ1800, August 17, 2023
   • 3 replies
   • 1.2k views
   • 
   • PFDennis
   • August 24, 2023

3. SuperSlicer Bed sheet PEI PNG not loading

   By therm_virtual0y, August 13, 2023
   • 5 replies
   • 10.7k views
   • 
   • therm_virtual0y
   • August 24, 2023

4. Skirts

   By Pappy3831, June 19, 2023
   • 7 replies
   • 918 views
   • 
   • PFarm
   • August 21, 2023

5. Question regarding TAP and Can Bus

   By pfm, August 20, 2023
   • 2 replies
   • 9.3k views
   • 
   • pfm
   • August 20, 2023

6. PIF discussion and questions

   By bdejong11129, April 19, 2023
   • 3 replies
   • 856 views
   • 
   • PFarm
   • August 19, 2023

7. Enraged rabbit

   By Pappy3831, May 12, 2023
   • 2 replies
   • 881 views
   • 
   • Poisson
   • August 18, 2023

8. Still can't get my TAP with Can to work.

   By mbunjes, July 2, 2023
   • 10 replies
   • 8.9k views
   • 
   • Glengus
   • August 18, 2023

9. CHOATICLAB Unboxing 1 2

   By mvdveer, May 1, 2023
   • 34 replies
   • 2.1k views
   • 
   • PFarm
   • August 17, 2023

10. Real Time Bed Leveling

    By Razor1666, February 17, 2023
    • 12 replies
    • 1.3k views
    • 
    • Razor1666
    • August 15, 2023

11. Klipper Mesh settings (Voron 2.4r1.5) & poor prints with new extruder stepper

    By RodimusPrime98, August 12, 2023
    • 3 replies
    • 2.8k views
    • 
    • VoronManiac
    • August 14, 2023

12. stealthburner gear ratio

    By prettyboyfpv, February 9, 2022   

    • sb
    • stealthburner
    • (and 1 more)

      Tagged with:

      • sb
      • stealthburner
      • gearratio
    • 10 replies
    • 19.5k views
    • 
    • D_Lj
    • August 11, 2023

13. mcu 'mcu': Unable to connect?

    By ken226, May 1, 2023
    • 18 replies
    • 9.6k views
    • 
    • TomTom2005
    • August 10, 2023

14. Building a high temp Voron (Trident) for PEEK - any ideas?

    By Buurman, April 22, 2023
    • 17 replies
    • 4.8k views
    • 
    • Buurman
    • August 6, 2023

15. Recurring hot end clog

    By RodimusPrime98, July 24, 2023
    • 5 replies
    • 1.4k views
    • 
    • claudermilk
    • August 5, 2023

16. Multiple Canbus Error - Printer shutdown after completing print

    By PFarm, July 25, 2023
    • 2 replies
    • 1.9k views
    • 
    • PFarm
    • August 3, 2023

17. Voron 2.4 with 2040 t5 extrusions.

    By RopusLongus, May 14, 2023
    • 2 replies
    • 25k views
    • 
    • kde
    • July 30, 2023

18. Voron 2.4 - Print_Start Macro suggestions.

    By nickpeck47, June 3, 2023
    • 9 replies
    • 9.6k views
    • 
    • Crashdown
    • July 30, 2023

19. can or can not

    By Wick, April 14, 2023
    • 16 replies
    • 3.5k views
    • 
    • Buurman
    • July 28, 2023

20. OMRON Solid State Relays

    By ChicagoKeri, July 26, 2023
    • 1 reply
    • 1.5k views
    • 
    • mvdveer
    • July 26, 2023

21. CanBus communication time-out possible solution plus question for Linux guru.

    By mbunjes, July 14, 2023
    • 6 replies
    • 4.5k views
    • 
    • PFarm
    • July 25, 2023

22. Bed Mesh Heightmap Results...

    By bcgreenbox, May 31, 2023   

    • bed mesh
    • heightmap
    • 3 replies
    • 3.4k views
    • 
    • spamttx
    • July 23, 2023

23. After last update, "Deprecated Klipper Option" message?

    By ken226, June 27, 2023
    • 2 replies
    • 9.1k views
    • 
    • GarthSnyder
    • July 18, 2023

24. RPI 3b question, just to be sure

    By mbunjes, July 11, 2023
    • 5 replies
    • 893 views
    • 
    • mbunjes
    • July 15, 2023

25. Voron 2.4 Heater extruder not heating at expected rate. Printing stopped and Error resulted. 1 2

    By SteveS, April 4, 2022
    • 42 replies
    • 17k views
    • 
    • mvdveer
    • July 12, 2023