General Discussion

431 topics in this forum

1. Klipper 2024

   By mvdveer, January 3
   • 9 replies
   • 1.2k views
   • 
   • YaaJ
   • January 6

2. 3D Printing RC Models

   By PFarm, December 10, 2023
   • 22 replies
   • 1.1k views
   • 
   • PFarm
   • January 5

3. Second layer problems

   By Cazze, December 31, 2023
   • 15 replies
   • 911 views
   • 
   • YaaJ
   • January 4

4. Question about RGB headers and LED Bars

   By cjkennedy72, December 30, 2023
   • 17 replies
   • 2.9k views
   • 
   • Buurman
   • January 4

5. Handy JST Pin loader video

   By Ducky4546, December 28, 2023
   • 9 replies
   • 883 views
   • 
   • mvdveer
   • January 1

6. Filametrix

   By YaaJ, December 30, 2023
   • 2 replies
   • 767 views
   • 
   • YaaJ
   • January 1

7. LDO LED stripes

   By YaaJ, December 28, 2023
   • 6 replies
   • 740 views
   • 
   • YaaJ
   • December 31, 2023

8. BIQU Microprobe

   By YaaJ, December 17, 2023
   • 3 replies
   • 817 views
   • 
   • YaaJ
   • December 27, 2023

9. Switchwire Conversion - Dual Y motors

   By Graymattor, September 5, 2023
   • 21 replies
   • 5.1k views
   • 
   • Paul Trautner
   • December 27, 2023

10. Enraged Rabbit V2 - A Colorful Christmas Present

    By Dirk, December 22, 2023
    • 11 replies
    • 3.7k views
    • 
    • YaaJ
    • December 25, 2023

11. The Health Hazards of 3D Printing

    By mvdveer, December 14, 2023
    • 19 replies
    • 4.3k views
    • 
    • Dirk
    • December 25, 2023

12. Voron 0.1 BTT M5P / CB1 Stepper Config issues

    By Titus A Duxass, December 9, 2023
    • 11 replies
    • 7.4k views
    • 
    • TitusADuxass
    • December 24, 2023

13. Voron 2.4 Nozzle Camera suddenly runs slow

    By TimGehres, December 22, 2023
    • 5 replies
    • 5.9k views
    • 
    • TimGehres
    • December 24, 2023

14. Superslicer -- Back again

    By mvdveer, December 17, 2023
    • 4 replies
    • 1.1k views
    • 
    • therm_virtual0y
    • December 23, 2023

15. Voron Test cube dimensional accuracy?

    By Beez1965, December 15, 2023
    • 20 replies
    • 9.8k views
    • 
    • dshess
    • December 22, 2023

16. Crowsnest Pi cam with Raspi SBC setup quirk

    By kenjesse_75, October 23, 2023
    • 5 replies
    • 8.9k views
    • 
    • kenjesse_75
    • December 21, 2023

17. Wall order

    By YaaJ, December 6, 2023
    • 12 replies
    • 1.8k views
    • 
    • YaaJ
    • December 19, 2023

18. 12 Days of Voronmas

    By Brystro, December 11, 2023
    • 1 reply
    • 906 views
    • 
    • 3dNutter
    • December 18, 2023

19. Tony Williams

    By Marbuck, December 5, 2023
    • 14 replies
    • 720 views
    • 
    • mvdveer
    • December 17, 2023

20. Rust prevention

    By Brystro, December 11, 2023
    • 3 replies
    • 485 views
    • 
    • 7milesup
    • December 17, 2023

21. Voron TAP comparisons 1 2

    By ChicagoKeri, October 1, 2023
    • 30 replies
    • 7.7k views
    • 
    • Dirk
    • December 15, 2023

22. LDO Trident Questions

    By kingstar, November 28, 2023
    • 5 replies
    • 423 views
    • 
    • kingstar
    • December 13, 2023

23. Octopus board V1.1 has double pins

    By mbunjes, December 4, 2023
    • 12 replies
    • 3.3k views
    • 
    • claudermilk
    • December 11, 2023

24. Stress test

    By YaaJ, December 3, 2023
    • 4 replies
    • 469 views
    • 
    • YaaJ
    • December 8, 2023

25. Extruder motor buzzing but not turning

    By bcgreenbox, May 19, 2023
    • 12 replies
    • 9.1k views
    • 
    • Hanna
    • December 8, 2023