Voron 2 - Questions

94 questions in this forum

1. BOM for stealthburner or afterburner

   Asked by Big H, August 17, 2023

   0 votes
   3 answers
2. Voron 2.4 bed not heating

   Asked by Yojuan, August 3, 2023

   0 votes
   4 answers
3. Phaetus rapido hotend burnout

   Asked by nannyogg82, February 1, 2023

   • phaetus
   • rapido
   0 votes
   8 answers
4. LGX Mount with EBB36, fan, and umbilical CANbus

   Asked by Rhonde, June 16, 2023

   0 votes
   0 answers
5. CANBOOT/SB2040/voron2.4

   Asked by mortalis, June 4, 2023

   0 votes
   0 answers
6. Stealthburner Printhead for Rapido rear CW2

   Asked by therm_virtual0y, May 31, 2023

   0 votes
   2 answers
7. Out of the blue, Voron 2.4 Part Fan turns on at startup.

   Asked by nickpeck47, May 18, 2023

   0 votes
   14 answers
8. Started getting z layer lines / poor quality walls when printing with my 2.4, running out of ideas and things to test

   Asked by Poisson, May 6, 2023

   0 votes
   12 answers
9. Which parts should I upgrade/reprint for an early V2.4 to V2.4r2?

   Asked by Yojuan, September 27, 2022

   • v2.4
   • v2.4r2
   • upgrade
   0 votes
   6 answers
10. Klipper connection issue after latest update

    Asked by Manny, May 2, 2023

    0 votes
    1 answer
11. Mandala Rose Kinematic Bed Mounts

    Asked by bdejong11129, April 24, 2023

    0 votes
    1 answer
12. Print Accuracy

    Asked by bdejong11129, April 15, 2023

    0 votes
    6 answers
13. Think I buggered my Pi

    Asked by nannyogg82, March 3, 2023

    1 vote
    30 answers
14. Parse Error - Fixed (sort of). Now nozzle bed heating issue.

    Asked by 7milesup, February 27, 2023

    0 votes
    30 answers
15. Software updates through Mainsail

    Asked by nannyogg82, March 21, 2023

    0 votes
    3 answers
16. Klicky not Docking

    Asked by Pierre52, February 22, 2023

    0 votes
    9 answers
17. While printing it pause randomly!!!

    Asked by Pradit, February 17, 2023

    0 votes
    7 answers
18. LGX Extruder Gears not turning

    Asked by BlueBleo, February 25, 2023

    0 votes
    7 answers
19. weird noise and belt rubing

    Asked by leo etchaas, February 23, 2023

    0 votes
    8 answers
20. Load and Unload Filament issue

    Asked by Pradit, February 17, 2023

    0 votes
    1 answer
21. Config file with TAP. HELP!

    Asked by 7milesup, February 5, 2023

    • tap
    0 votes
    62 answers
22. Circular accuracy when printing

    Asked by nannyogg82, February 1, 2023

    0 votes
    4 answers
23. Quad_Gantry_Level error

    Asked by shiftynick, January 29, 2023

    0 votes
    14 answers
24. Tap Heat Dissipation - Just melted through hot end carrier

    Asked by Todd, January 10, 2023

    • tap
    0 votes
    12 answers
25. HELP!!! FILAMENT CLOG IN THE MIDDLE.

    Asked by Pradit, January 24, 2023

    0 votes
    12 answers