Voron 2 - Questions

118 questions in this forum

1. nitehawk SB printer.cfg changes and sensorless homing

   Asked by mvingtargt, July 10

   0 votes
   6 answers
2. Which display to use?

   Asked by Guest, December 4, 2023

   0 votes
   9 answers
3. Voron 2.4r2 back panel issue

   Asked by SamppaD, June 30

   0 votes
   4 answers
4. Arthur

   Asked by Arthur, May 4

   0 votes
   1 answer
5. Z Drive Belt Tensioner Not Tight Enough

   Asked by Eximius2286, January 27, 2024

   0 votes
   3 answers
6. voron 2.4 parts are alot smaller on the z than they should be. seeing if i can get help

   Asked by twitch3d, February 20

   0 votes
   2 answers
7. Salmon Skin\Wood Grain. Please help

   Asked by Walkerfever, February 1

   0 votes
   9 answers
8. Chaoticlab Tap V2/QGL question

   Asked by SamppaD, January 6

   1 vote
   3 answers
9. sb2209 rp2040 looses connectivity after a few power cycles

   Asked by rcjunkie, November 11, 2025

   0 votes
   0 answers
10. Automatic Shutdown Set-up with BTT Relay V1.2 with Octopus Pro V1.1

    Asked by zjudy, November 5, 2024

    0 votes
    2 answers
11. Voron 2.4r2 Ldo stepper motor kit,question about current.

    Asked by SamppaD, December 29, 2024

    0 votes
    7 answers
12. z_thermal_adjust

    Asked by therm_virtual0y, February 15, 2024

    1 vote
    10 answers
13. Blobifier

    Asked by DC67, April 6, 2025

    0 votes
    0 answers
14. Serious difficulty in getting the material to adhere to the plate

    Asked by Rede, March 20, 2025

    0 votes
    4 answers
15. Raspberry Pi 4B not connecting to wifi. No IP address

    Asked by NewGradRN, February 16, 2025

    0 votes
    15 answers
16. Nothing ventured, nothing gained (Voron 2.4 used purchase recovery)

    Asked by scyyie, January 27, 2025

    0 votes
    19 answers
17. 2 Probes in Klipper?

    Asked by DC67, February 2, 2025

    0 votes
    0 answers
18. Voron 2.4r2 seems to lose printhead position??

    Asked by shiftynick, December 12, 2024

    0 votes
    3 answers
19. Pi camera v2 on Raspberry Pi OS Bookworm

    Asked by thien, September 27, 2024

    0 votes
    0 answers
20. R2. Stealthburner (canbus) and Tap. "XY axis Endstop PCB" or Tap mounted individual switch?

    Asked by Pauly, June 27, 2023

    0 votes
    7 answers
21. BTT Manta M8P with CM4 connected to BTT Pi TFT50 V2.1 display

    Asked by Kaye7877, January 29, 2024

    0 votes
    2 answers
22. Beacon H - Z-offset

    Asked by cbix, August 30, 2024

    0 votes
    3 answers
23. Persisting Z-Height Calibration Issue

    Asked by Durahl, August 6, 2024

    0 votes
    0 answers
24. Vertical banding on X

    Asked by celulari, June 11, 2024

    0 votes
    2 answers
25. v2.4 SD card full

    Asked by TitusADuxass, June 5, 2024

    0 votes
    31 answers